| 17.05.2017 ENG 824 |
Product | PET MATT WHITE TC 50 / RC15 / HD 70 |
Sales Code | |
EAN | |
Product use | Product designed for durable labelling applications on surfaces such as steel, glass and ABS. It will perform for the lifetime of the labelled product with very good adhesion and very good print resistance against chemicals, UV-light, heat and moisture. |
|
Face | PET MATT WHITE TC 50 |
Product | White, matt top-coated polyester film. |
Substance | |
Caliper | |
Tensile strength MD | |
Tensile strength CD | |
Opacity | |
Printability | Suitable for flexography, screen and offset printing methods. Special inks designed for non-absorbent materials should be used. |
|
Adhesive | RC15 |
Type | Clear permanent adhesive. |
Composition | Radiation-cured UV-Acrylic. |
Tack min | |
Peel 180º | 20 | N/25mm | FTM 1 | (20 min on glass) |
|
Backing | HD 70 |
Product | A white transparent glassine backing paper. |
|
Substance | |
Caliper | |
Tensile strength MD | |
Transparency | |
Performance | |
Minimum labelling temperature | |
Service temperature | Temperature resistance of label applied to glass. Other substrates should be tested under original conditions.
Test Conditions | Visual Appearance | +150 °C for 24h on glass | no significant change | -40 °C for 72h on glass | no significant change |
|
Shelf life | From the date of manufacture: 2 years at +20°C and RH50%. Prolonged storage at higher temperatures and/or humidity levels will shorten the shelf life. |
|
Information | |
Adhesive coatweight | |
Adhesion | Due to the fact that the adhesive needs a certain time to reach its final adhesion, we recommend waiting at least 24h (better 72h) after dispensing the label to the substrate before proceeding with any performance tests.
Test Conditions: 23°C, 50%RH FTM1: 180° Peel Adhesion (300 mm/min) with 72 h dwell time.
Surface | [N/25mm] | Stainless Steel | 21.8 | ABS | 25.3 | Polycarbonate | 27.4 | Polypropylene | 6.5 | HDPE | 9.1 | PA6 | 13.4 | PA6 + GF30 | 16.8 | Polyester | 17.6 | Lacquered panel | 12.7 | Powder coated panel | 14.0 |
|
Chemical resistance | Test Conditions: Dwell time on glass plate: 24 h; 23°C 50% RH Immersion in chemical: 4 h; 23°C 50% RH
Chemical | Visual Appearance | Edge Penetration (mm) | Brake Fluid | no change | 0 | Engine Oil | no change | 0 | Diesel | no change | 0 | Distilled Water | no change | 0 | Dish Washing Agent | no change | 0 | Bleach | no change | 0 |
|
Approvals | |
Typical values | The listed technical data are typical values and give indications about the performance of the material only. They are not intended for specification purpose. |
|
|
|
Disclaimer | The performance of the product should always be tested in the actual application conditions. Our recommendations are based on our most current knowledge and experience. As our products are used in conditions beyond our control, we cannot assume any liability for damage caused through their use. Users of our products are solely responsible that the product is suitable for its intended application, and have determined such at their sole discretion. Users must comply with any applicable legislation and/or testing requirements for the finished article, and are responsible for bringing their products to market.
This publication does not constitute any warranty, express or implied, and is intended only for the recipient and cannot therefore be transferred to any third party. We cannot assume any liability for the use of our products in conjunction with other materials. All our products are sold subject to UPM Raflatac’s general sales conditions, and you should ensure that any existing laws are observed.
This publication replaces all previous versions. All information is subject to change without notice.
|